Sign up for our newsletter to get the latest news and specials!




Home > Blems
Sort By:
Page of 1
Offset Flame Arrestor Adapter 44mm
Offset Flame Arrestor Adapter 44mm
Our Price: $30.00

Here is a good solution when you need more clearance from the hull. These flame arrestor adapters move the entire flame arrestor almost 3/8 inch in any direction.
Made from billet aluminum, 44mm size
This is a blemished product. Perfectly functional, just cosmetically chllenged
more info
Billet Superjet Motor Mount
Billet Superjet Motor Mount
Our Price: $40.00

These mounts are made from 6061 anodized aluminum for corrosion protection and a long life. The urethane is co-molded into the base and the threaded insert to provide a one piece, mechanical lock on all components. These mounts do not rely on glue to hold things together, the mount is molded at one time with the billet threaded insert and the billet aluminum base. These are made to the highest standards in our own manufacturing facility right here in the USA. There is 4 years of R&D that went into making these mounts.
These are blemished product. Structurally sound in fit and finish. We like to call them cosmetically challenged.
Motor mounts sold individually.

more info
Yamaha 701 Intake speed plate
Yamaha 701 Intake speed plate
Our Price: $65.00

This allows you to convert your OEM Yamaha 62t intake to an o-ring setup. Never change gaskets again on your 62t intake.
Uses the stock mikuni 38mm carbs.
Anodized 6061 aluminum and all stainless hardware
more info
Yamaha 760 Intake speed plate
Yamaha 760 Intake speed plate
Our Price: $70.00

This allows you to convert your OEM Yamaha 64x intake to an o-ring setup. Never change gaskets again on your 64x intake. Available in 44mm 6061 aluminum and all stainless hardware
This is a used, good condition part.
more info
Kawasaki 440-550 to Kawasaki 650-750-800 Engine Conversion
Kawasaki 440-550 to Kawasaki 650-750-800 Engine Conversion
Our Price: $75.00

These plates allow you to bolt up a Kawasaki 650-750-800 engine into a Kawasaki 440-550 using the stock 440-550 engine plate. These are the lightest in the industry and made from 6061 aluminum. All stainless hardware is included for the swap. The only kit on the market with 2 engine positions. This allows you to fine tune the ride of the ski by relocating the motor. You can use the stock 650-750 coupler or a re-tapped 550 coupler.
These are blemished product, they are functional in fit and finish, just cosmetically challenged. Save on these in limited quantities
more info
Kawasaki 550 Conversion Bearing
Kawasaki 550 Conversion Bearing
Our Price: $155.00

This bearing assembly is used to convert your js440 or is550 to run a 550sx pump. Allows you to convert an early hull to a later floating bearing drive. Made from all anodized aluminum and high temp silicone rubber. Stainless Bearing and high quality seals are included and pre-installed. Ready to run.
This is a blemished product, structurally sound and new, just cosmetically challenged
more info
Yamaha 650-701-760 engine in a Kawasaki 650-750-800 hull
Yamaha 650-701-760 engine in a Kawasaki 650-750-800 hull
Our Price: $230.00

This kit works in any kawasaki 650-750-800 hull and allows you to run a yamaha 650-701-760 motor. The kit contains conversion plates, special height billet motor mounts, and all hardware and instructions to make the conversion. All components are either anodized 6061 aluminum or stainless steel. All that is needed is an ADA Yamaha engine coupler to mate up to the Kawasaki driveline. This conversion kit is simple to complete, all the hard work has been done for you.
This is a blemished product. It is functional in fit and finish, just cosmetically challenged.
more info
   
 
Copyright ©  rhaas products. All Rights Reserved.
Built with Volusion