|
|
|
|
|
|
engine lock washer
|
|
|
These are extra thick washers for bolting your engine to the motor mount. They have teeth to dig in to the bedplate and prevent the engine from slipping. Made from 6061 aluminum and anodized to prevent corrosion. Sold individually in either 8mm or 10mm size.
|
|
|
|
|
|
|
|
|
|
Fuel Line Restrictor .030
|
|
|
Fuel line restrictor is installed in the return line from the carburetor to the tank. This raises the fuel pressure in the system, a necessity when using a remote fuel pump. Size is .030"
|
|
|
|
|
|
|
|
|
|
Steering Cable Extender 1"
|
|
|
Extend your steering cable easily with this extension. Made from 6061 aluminum and anodized for corrosion resistance.
Your Choice, M5x0.8 thread or M6x1.0 thread
|
|
|
|
|
|
|
|
|
|
Steering Cable Extender 2"
|
|
|
Extend your steering cable easily with this extension.
Extends cable 2 inches.
Made from 6061 aluminum and anodized for corrosion resistance.
Your Choice, M5x0.8 thread or M6x1.0 thread
|
|
|
|
|
|
|
|
|
|
Carb Brace Top Mount Dual Carbs
|
|
|
Carb brace for dual Mikuni carbs. Mounts to the Two holes on the top of the carb.
Made from 6061 aluminum and anodized for corrosion resistance.
Comes with all hardware.
Available in 104mm spacing for early dual carb manifolds, or 117mm-120mm spacing for Standard Yamaha and Kawasaki spacing
|
|
|
|
|
|
|
|
|
|
Mikuni Fuel Pump Block Off
|
|
|
Fuel pump block off for Mikuni carbs. This is needed when running a remote fuel pump. Made from billet 6061 aluminum and anodized for corrosion resistance.
Comes with instalation hardware as well.
|
|
|
|
|
|
|
|
|
|
Carb Brace Top Mount TrippleCarbs
|
|
|
Carb brace for tripple Mikuni carbs. Mounts to the Two holes on the top of the carb.
Made from 6061 aluminum and anodized for corrosion resistance.
Comes with all hardware.
Available in 104mm spacing for early dual carb manifolds, or 117mm-120mm spacing for Standard Yamaha and Kawasaki spacing
|
|
|
|
|
|
|
|
|
|
Carb Brace Fuel Pump Mount Dual Carbs
|
|
|
Carb brace for dual Mikuni carbs. Mounts to the fuel pump housing. Perfect for aftermarket carbs that do not have the 2 top holes. Works with fuel pump block off plates as well.
Made from 6061 aluminum and anodized for corrosion resistance.
Comes with all hardware.
Available in 104mm spacing for early dual carb manifolds, or 117mm-120mm spacing for Standard Yamaha and Kawasaki spacing
|
|
|
|
|
|
|
|
|
|
Billet Polaris Octane Motor Mount
|
|
|
These mounts are made from 6061 anodized aluminum for corrosion protection and a long life. The urethane is co-molded into the base and the threaded insert to provide a one piece, mechanical lock on all components.
These mounts do not rely on glue to hold things together, the mount is molded at one time with the billet threaded insert and the billet aluminum base. These are made to the highest standards in our own manufacturing facility right here in the USA.
There is 4 years of R&D that went into making these mounts the best you can buy for your Polaris Octane.
Motor mounts sold individually.
|
|
|
|
|
|
|
|
|
|
Water Outlet Bilge Combo
|
|
|
Water outlet plate for all watercraft. Has 2 water outlets and a bilge outlet in one billet plate. water outlets use 1/8 NPT fittings on the backside to make them fit any hose size. Bile outlet accepts 3/4 inch bilge line.
Made from billet 6061 aluminum and clear anodized for protection from the elements.
Comes with installation hardware as well.
|
|
|
|
