|
|
|
|
|
|
engine lock washer
|
|
|
These are extra thick washers for bolting your engine to the motor mount. They have teeth to dig in to the bedplate and prevent the engine from slipping. Made from 6061 aluminum and anodized to prevent corrosion. Sold individually in either 8mm or 10mm size.
|
|
|
|
|
|
|
|
|
|
Fuel Line Restrictor .030
|
|
|
Fuel line restrictor is installed in the return line from the carburetor to the tank. This raises the fuel pressure in the system, a necessity when using a remote fuel pump. Size is .030"
|
|
|
|
|
|
|
|
|
|
Steering Cable Extender 1"
|
|
|
Extend your steering cable easily with this extension. Made from 6061 aluminum and anodized for corrosion resistance.
Your Choice, M5x0.8 thread or M6x1.0 thread
|
|
|
|
|
|
|
|
|
|
Steering Cable Extender 2"
|
|
|
Extend your steering cable easily with this extension.
Extends cable 2 inches.
Made from 6061 aluminum and anodized for corrosion resistance.
Your Choice, M5x0.8 thread or M6x1.0 thread
|
|
|
|
|
|
|
|
|
|
Mikuni Fuel Pump Block Off
|
|
|
Fuel pump block off for Mikuni carbs. This is needed when running a remote fuel pump. Made from billet 6061 aluminum and anodized for corrosion resistance.
Comes with instalation hardware as well.
|
|
|
|
|
|
|
|
|
|
Carb Brace Top Mount Dual Carbs
|
|
|
Carb brace for dual Mikuni carbs. Mounts to the Two holes on the top of the carb.
Made from 6061 aluminum and anodized for corrosion resistance.
Comes with all hardware.
Available in 104mm spacing for early dual carb manifolds, or 117mm-120mm spacing for Standard Yamaha and Kawasaki spacing
|
|
|
|
|
|
|
|
|
|
Factory Pipe Head Pipe Bolts
|
|
|
Replace those rusty stock bolts with these stainless bolts. This is a rare size to find in the states, but we have sourced them and bring them to you for a reasonable price. Thread is M10x1.25 Sold as a set of 3.
Yamaha head pipes use the 40mm long, Kawasaki head pipes use the 50mm long.
|
|
|
|
|
|
|
|
|
|
Billet Steering Nut
|
|
|
This is an all aluminum steering nut for Kawasaki steering cables. They are anodized for corrosion resistance, and use a 19 mm wrench to remove and install.
|
|
|
|
|
|
|
|
|
|
Carb Brace Fuel Pump Mount Dual Carbs
|
|
|
Carb brace for dual Mikuni carbs. Mounts to the fuel pump housing. Perfect for aftermarket carbs that do not have the 2 top holes. Works with fuel pump block off plates as well.
Made from 6061 aluminum and anodized for corrosion resistance.
Comes with all hardware.
Available in 104mm spacing for early dual carb manifolds, or 117mm-120mm spacing for Standard Yamaha and Kawasaki spacing
|
|
|
|
|
|
|
|
|
|
Billet Bottom Plate for Kawasaki Start Stop Housing
|
|
|
Tired of your cracked up bottom plate on your SXR style start stop housing?
This is our billet replacement. Made from 6061 aluminum and anodized for corrosion resistance. This will last.
Your choice of silver or Black.
|
|
|
|
